Specifications:

Precision: ±0.01V

Low-voltage alarm mode: 2S-8S

Total voltage test: 0.5V-36V Group voltage test: 0.5V-4.5V

1S test voltage: 3.7V-30V

Alarm voltage setting: OFF-2.7V-3.8V

Size: 40 x 25 x 11mm/1.6" x 1.0" x 0.4"(L x W x H)

Features:

High accuracy, prevent over-charge or over-discharge.

Use for 1-8s Li-Po/Li-ion/Li-Mn/Li-Fe batteries.

ABS Material shell, anti-impact and heat resistance.

LED display, large and clear font with loud sound.

Compact design, easy to carry and connect.

1.1-8s Lipo Battery Voltage Tester, Low Voltage Alarm Mode for 2-8S, Function of Checking Your Lipo Cells Voltage,with LED Display, Large and Clear Font with Loud Sound, Compact Design, Easy to Carry and Connect.

2.Use for 1-8s Lipo/Li-ion/LiMn/Li-Fe,Automatic Protects Against Reverse Connection.

3.There is a Low-Voltage Alarm Function, when the Voltage is Lower than the Set Alarm Value, there will be an Audible Alarm to Avoid Over-Discharge of the Battery.

4.ABS Material shell, Protect the Product, and have a Better Appearance, Measuring the Voltage of the Single-Chip Battery is Accurate,High Accuracy, Prevent Over-Charge or Over-Discharge, Anti-Impact and Heat Resistance

5.When the Voltage is Below the Set Value,It Will Buzzer with Red LED Light,Pre-set Value 3.3V.Push Key which Can Change the Voltage Settings and Save

• Specifications:

  
  

  Use for 1-8s Lipo/Li-ion/LiMn/Li-Fe.

  Function of Checking Your Lipo Cells Voltage.

  Voltage Display Function and Low Voltage Alarm Funtion.

  Protect the Battery From Overcharging or Overdischarging.

  Test the Working State of Lithium Battery.

  Automatic Protects Against Reverse Connection.

  Each Size: 4*2.5*1.1cm

  Each Weight: 9g

  
  

  Battery Voltage Display:

  Voltage Detection Pricision: 0.01V.

  Unit Voltage Display Range: 0.5V-4.5V.

  Total Voltage Display Range: 0.5V-36V.

  1S Test Mode Voltage ange: 3.7v-30v.

  
  

  Alarm Mode:

  Low Voltage Alarm Mode for 2-8S.

  Alarm Set Value Range: OFF-2.7V-3.8V.

  When The Voltage is Below the Set Value,Tester Will Buzzer with Red LED Light, Pre-set Value 3.3V. Push Key Which Can Change The Voltage Settings and Save.

  
  

  Tips:

  When the voltage is lower than the alarm value, it will beep constantly .

  When the product of the measured is unpluged, the alarm will stop.

  Or When the cells recover they will stop beeping .

  
  

Product introduction:
    This voltage indicator is used for 1S~8S lithium battery detection, and automatically detects the voltage and total voltage of each cell of the lithium battery. It supports reverse connection protection.
    It allows you to know the working status of your battery anytime and anywhere, so that the battery will not be damaged by over-discharge or over-charge.

    Whether it is in flight or in idle state, you can plug the electric display into the battery balance charging connector to understand the battery power status.

It is a must if there is no multimeter!

    When the voltage is lower than the set value, the buzzer will sound and the red LED light will flash; the set value is 3.3V, press the button to change the voltage set value and automatically save the user's current set value.

Product parameters:

1. For 1S-8S lithium battery detection
2. Voltage detection accuracy: ± 0.01V.
3. Group voltage display range: 0.5V~4.5V
4. Total voltage display range: 0.5V~36V
5.1S test mode voltage range: 3.7V~30V
6. Low voltage buzzer alarm mode 2S-8S
7. Alarm voltage setting range: OFF~2.7~3.8V
8. Size: 40mm x 25mm x 11mm Weight: 9g

Instructions:

    Put the front of the electric display up (the side of the digital display), and point it at yourself. Insert the white balance charging plug of the battery along the pins on the left of the electric display. If there is no response, just plug the balance charging plug backwards. There is a small button on the other end of the electric display, which is used to set the alarm voltage of the electric display.

This product is suitable for various kinds of RC battery, such as LiPo/Li-ion/Li-Mn/Li-Fe Battery. When the voltage is below the set value, it will buzzer with red LED light, pre-set value 3.3V. Push the key which can change the voltage setting and save.

Features:
Sharp backlit LCD screen, applicable under poor light condition
Compact and extremely portable
Suitable for various kinds of RC battery, such as LiPo/Li-ion/Li-Mn/Li-Fe Battery
Easy to install

Specification:
Weight: 14g
Dimension: 44 * 32 * 14mm
Display: LED
Voltage detection precision:±0.01V
Unit voltage display range:0.5-4.5V
Total voltage display range:0.6-36V
1S test mode voltage range: 3.7-30V
Low voltage alarm mode for:2-8S
Alarm set value range: OFF-2.7-3.8V

Package includes:
1PCS/2PCS x Lipo Battery Voltage Tester